36

I try to read up on diffraction limiting and gaussian beams, but it always gives a result saying it’s characterized by an angle which is the edges of a cross section of a cone. Which says nothing on the physical limits of how I choose that angle. It just describes (once far away from the narrowest point) the shape of a cone: width is proportional to distance from the narrowest spot.

So what’s to prevent you from describing a laser that's arbitrarily tight, at some arbitrary distance, and learning that the required angle is very close to 0?

What, in principle, prevents this from happening?

In Robert L. Forward’s “hard science fiction” novel he based the lightsail description on actual research but did not go into detail in the novel. As a plot point, the senders had to enlarge the size of a focusing device (probably a zone plate) to send the beam for breaking, so the larger sending aperture was necessary for a longer distance. Now they didn’t finish in time due to funding but saved the mission by doubling the light frequency instead. So that sounds like a diffraction effect.

I suppose the relationships of what is possible is simply scaled by wavelength, and once you divide that out there is some relationship between the possible size of the emitter, size of the target, and separation between them? Why does making the emitter larger allow the target to be smaller?

To use some concrete numbers, suppose the target is a lightsail 1 light year away, and it is 1 Mm in diameter. The wavelength in Forward’s story was green light, and if higher frequency allows better focus than the best beam would be the highest frequency that doesn’t start causing issues by breaking bonds in the atoms reflecting it, so just past visible where UV begins. What size emitter (final focusing device) would be needed?

Qmechanic
  • 201,751
JDługosz
  • 5,297
  • 2
    As a point of practical comparison, in laser ranging of the Earth's moon with contemporary equipment, the beam ends up kilometers wide at the lunar surface. – Chris Stratton Sep 13 '16 at 05:45
  • Yes, but much of that is an imperfect beam to begin with. If you could engineer a perfect beam to start with, how much would it still spread? – JDługosz Sep 13 '16 at 21:45
  • 1
    I'd be interested to know if self-focusing laser beams in a vacuum is plausible, for example as discussed in this journal article. – Xavier Sep 14 '16 at 06:44

2 Answers2

40

So what’s to prevent you from describing a laser that's arbitrarily tight, at some arbitrary distance, and learning that the required angle is very close to 0?

The half angle of divergence is given by

$$\theta = \frac{\lambda}{\pi w_0}$$

where $w_0$ is the beam diameter at its narrowest point (the waist, or focal point), and $\lambda$ is the optical wavelength.

Typically with a laser the waist point is at the output aperture of the laser cavity, and the beam diverges from there. If you built your laser with a converging output, you'd push the waist point out along the z direction (the direction of propagation) but you'd also reduce the waist diameter, so ultimately increase the divergence angle.

So you can't choose to produce an arbitrarily small divergence angle unless you're prepared to build a laser with an arbitrarily large output aperture.

To use some concrete numbers, suppose the target is a lightsail 1 light year away, and it is 1 Mm in diameter.

1 light year is about $10^{16}$ meters. So you need a divergence angle on the order of $10^6 / 10^{16}$, or $10^{-10}$ radians. You need a beam waist of

$$ w_0 > \frac{\lambda}{\pi \theta} $$

If your wavelength is 500 nm, this means a waist of at least 1600 m. In practice I expect there would be "unique engineering challenges" in designing optics close enough to ideal to achieve this kind of divergence. I've never heard of beam divergence being measured in units smaller than milliradians, but I don't know what's been achieved in hero experiments.

Will Vousden
  • 1,239
The Photon
  • 27,393
  • 3
    You can work around the limitation of the laser size by using a beam expander. But that changes nothing fundamental. The beam waist is still limited by the size of your optics, and the diffraction angle is determined by the beam waist. Also the discussion so far is for a Gaussian beam. A beam with a Bessel cross section can have a diffraction angle of 0. – mmesser314 Sep 13 '16 at 04:45
  • 1
    @mmesser314, I haven't encountered the Bessel beam before, but wiki says it only has 0 diffraction if it has infinite spatial extent. Is there a known relationship for diffraction angle of a Bessel beam that's been truncated by a given aperture? – The Photon Sep 13 '16 at 04:49
  • 2
    It is similar to a Gaussian beam, which also needs an infinite spatial extent to be truly Gaussian. The beam gets dimmer as you get farther off axis. The beam diameter of a Gaussian beam is defined as the diameter where the power is down by a factor of $1/e^2$. The industry standard is to use optics 1.5 x the beam diameter. That is where the power is down to 1% of the center. For most purposes, this has a negligible affect on the beam. – mmesser314 Sep 13 '16 at 04:56
  • @mmesser314 your first comment helps, thanks! – JDługosz Sep 13 '16 at 05:20
  • If the target being focused on is 10^6 m in diameter, and you used this to get the needed angle. But then you compute a different (much smaller) waist! I thought the spot I’m focusing to is the waist. – JDługosz Sep 13 '16 at 05:45
  • 1
    No, the waist is at your transmitter. You are trying to make the divergence angle small enough that the beam doesn't get bigger than the target by the time it gets there. Unless you want to build a transmitter that is bigger than your target, but generally the goal is to minimize the size of the transmitter. – The Photon Sep 13 '16 at 05:52
  • You wrote «narrowest point (the waist, or focal point)» and I start with a focusing device and aim at the sail I focus on. I had a hard time reading your answer because of different interpretations.

    Yes, the emitter (Forward’s huge zone plate) is large: you want the larger mass to be the one that remains at home, and the smaller one to be the one undergoing acceleration.

     – JDługosz Sep 13 '16 at 21:32
  • 2
    In that case, you can make it as large as you want. There is no upper limit based on diffraction effects. – The Photon Sep 13 '16 at 21:50
  • So if you had a bunch of smaller lasers spread out over 1.6 km and coordinate, does that fulfill the criterion? – Superbest Sep 13 '16 at 23:05
  • @Superbest, if you can keep those lasers phase locked to each other to an incredible degree of accuracy, it should do. For that matter there may be some trick you could do with just 2 or 3 or 4 sources spread over a few km, pretty much the same way we use a few small telescopes to achieve tiny angular resolutions in astronomy. – The Photon Sep 13 '16 at 23:35
  • 1
    "Unique engineering challenges" - AHAHA – iAdjunct Sep 14 '16 at 03:45
  • 1
    specs for the Laser Interferometer Space Antenna (Gravitational Wave Observatory) called for a divergence angle of 4e-6 radians – Markus Schmassmann Sep 14 '16 at 13:12
  • Pardon my ignorance, but what is a "hero experiment"? – Travelling Man Sep 14 '16 at 15:10
  • @TravellingMan, admittedly it's not very grammatical, but it's what we used to call an experiment where you do whatever necessary (or pay whatever necessary) to improve some experimental parameter(s). – The Photon Sep 14 '16 at 15:15
13

As with all other fields in physics, much of what one observes in optics is governed by scales. These scales are typically: the wavelength $\lambda$, the size of the beam (smallest beam radius $w_0$ or aperture radius $R$) and the propagation distance $z$ (or focal length $f$).

For simplicity let's assume that we have a Gaussian beam (even if we don't, we can still use these relations, with the understanding that things can then only be worse). If I produce a laser beam with a flat wave front (no curvature) with a given size and given wavelength, then that beam will inevitable start to diverge with a beam divergence angle $\theta$ given by $$ \theta = \frac{\lambda}{\pi w_0} . $$

Now say we want to try and counteract the divergence by adding a converging phase to the beam. It would be like sending the beam through a lens first. For comparison we keep the size of the beam with the converging phase the same as before. Sure enough the beam will first converge to a focal point, but then after that it will start to diverge again. This time the divergence angle would be larger, because the minimum size of the beam, which was obtained at the focus is now smaller and the beam divergence angle is based on this smallest size.

What is the size of the focal spot? A lens actually implements a Fourier transform. So the relationship between the beam size before the lens and the size of the focus (beam radius at focus: $w_f$) is governed by this Fourier relationship between Gaussian functions: $$ \tag{1} w_f = \frac{\lambda f}{\pi w_0} $$ Often the beam size is given by the aperture size of the system (lens). In such a case one can replace $w_0$ by the radius of the aperture $R$. Then we see that for a given focal length and wavelength the size of the focal spot becomes smaller as the aperture becomes larger. (That's why they needed a large aperture in the story.)

What if we try to produce the focused spot at an astronomical distance away from us? Turns out there is a maximum distance at which we can `throw' the beam waist (focus). This distance is given by the Rayleigh range of the output beam: $$ z_{\rm Rayleigh} = \frac{\pi w_f^2}{\lambda} . $$ So we see that, in order to increase this distance, we would also have to increase the size of the beam. So in the end one cannot win.

flippiefanus
  • 14,614
  • I modified the notation slightly to distinguish between the emitter size $R$ and the beam radius $w_0$. The tightest focus is given by the second expression [Eq (1)]. Here you can replace $w_0$ by $R$ (provided that the wavefront is still more or less flat in the aperture). – flippiefanus Sep 13 '16 at 05:34
  • "let's assume that we have a Gaussian beam (even if we don't, we can still use these relations, with the understanding that things can then only be worse)." - someone else said that a Bessel beam can have no diffraction, which is not worse. But then, that's also in the limit of infinite aperture size. – user253751 Sep 14 '16 at 00:15
  • The thing about a Bessel beam is that since one cannot produce one with an infinite aperture, it only remains a Bessel-like beam for a finite range. After that is also starts to diverge. – flippiefanus Sep 14 '16 at 04:30